穿條機啟動不了可能有多種原因，以下是一些可能的故障原因及其解決方法：

　　There may be multiple reasons why the strip threading machine cannot start. Here are some possible causes of the malfunction and their solutions:

　　1. 外部總電源未接通：檢查外接電源是否連接正常，確保電源線沒有損壞，重新送電。

　　1. External main power supply not connected: Check if the external power supply is connected properly, ensure that the power cord is not damaged, and re power on.

　　2. 內部控制電源未接通：使用鑰匙開關打開電源或合上配電柜內的開關。

　　2. Internal control power not connected: Use the key switch to turn on the power or close switch 1 inside the distribution cabinet.

　　3. 暫停按鈕按下不起：檢查暫停按鈕是否被按下，如果按下，嘗試再按一下讓它彈起復位。

　　3. Pause button cannot be pressed: Check if the pause button is pressed. If it is pressed, try pressing it again to make it pop up and reset to .

　　4. 急停按鈕按下：檢查急停按鈕是否被按下，如果按下，放開急停按鈕。

　　4. Emergency stop button pressed: Check if the emergency stop button is pressed. If it is pressed, release emergency stop button .

　　5. PLC損壞：如果PLC（可編程邏輯控制器）損壞，建議重新更換。

　　5. PLC damage: If the PLC (programmable logic controller) is damaged, it is recommended to replace it with a new one.

　　6. 保險絲燒壞：檢查保險絲是否燒壞，如果燒壞，建議更換保險絲。

　　6. Fuse burnt out: Check if the fuse is burnt out. If it is burnt out, it is recommended to replace fuse .

　　7. 電源線與其他設備損懷：檢查電源線是否與其他設備有損壞或干擾，重新接獨立電源。

　　7. Damage to power cord and other devices: Check if the power cord is damaged or interferes with other devices, and reconnect the independent power supply .

　　4d33737a6bf7dd9

　　8. 變頻器緩起啟動設置過長：如果自動纏繞機轉盤需要人推才能啟動，可能是變頻器緩起啟動設置的起動時間太長，重新設定。

　　8. The slow start setting of the frequency converter is too long: If the automatic winding machine turntable requires human pushing to start, it may be due to the slow start setting of the frequency converter being too long. Reset .

　　9. 撥碼開關損壞：檢查撥碼開關是否損壞，如果損壞，則檢修撥碼開關。

　　9. Damaged dip switch: Check if the dip switch is damaged. If it is damaged, repair dip switch .

　　10. 轉盤鏈條斷裂：檢查轉盤鏈條是否斷裂，調整大小鏈輪之間的距離，連接鏈條，如果是鏈條損壞則更換鏈條。

　　10. Broken turntable chain: Check if the turntable chain is broken, adjust the distance between the size chain wheels, connect the chain, and if the chain is damaged, replace chain .

　　11. 轉盤電機或減速機故障：檢查轉盤電機和減速機是否工作正常，如有故障，建議更換。

　　11. Fault in turntable motor or reducer: Check if the turntable motor and reducer are working properly. If there is a fault, it is recommended to replace them.

　　12. 旋鈕損壞：檢查旋鈕是否損壞，如果是，更換旋鈕。

　　12. Knob damage: Check if the knob is damaged, and if so, replace knob .

　　13. 轉盤減速機與鏈輪連接不正常：檢查連接是否正常，換連接平鍵。

　　13. The connection between the turntable reducer and the sprocket is abnormal: check if the connection is normal and replace it with the flat key .

　　14. 變頻器顯示過載報警：如果變頻器顯示過載報警，檢查電壓是否穩定，改善電源品質或調整變頻加減速時間。

　　14. Overload alarm displayed on the frequency converter: If the frequency converter displays an overload alarm, check if the voltage is stable, improve the quality of the power supply, or adjust the acceleration and deceleration time of the frequency converter.

　　如果上述方法都不能解決問題，建議聯系專業的維修人員進行檢查和維修。在進行維修時，請確保安全第一，避免因操作不當造成人身傷害或設備進一步損壞。

　　If none of the above methods can solve the problem, it is recommended to contact professional maintenance personnel for inspection and repair. When carrying out repairs, please ensure safety first and avoid personal injury or further damage to equipment caused by improper operation.

　　本文由穿條機提供幫助，更多的相關內容請點擊：http://m.tzjddl.cn希望本文能夠為您帶來幫助，感謝您的閱讀！

　　This article is assisted by the threading machine. For more related content, please click: http://m.tzjddl.cn I hope this article can be helpful to you. Thank you for reading!